City guide
Plumbers in Seattle, WA
A local guide to plumbing in Seattle, Washington (King County): numbers on housing, weather and utilities, plus what to check before you hire a plumber.
- Population
- About 780,995 residents (U.S. Census Bureau 2024 estimate)
- County
- King County, Washington
- Homes
- Median year built 1976; 53% of homes built before 1980, 33% since 2000
- Housing mix
- 37% detached single-family houses; 44% of homes owner-occupied
- Home heating fuel
- Electricity 61%, utility gas 33%, fuel oil 3%
- Winter
- Average winter daily low 37°F; about 25 nights a year at or below 32°F
- Summer
- Average summer daily high 74°F; about 2 days a year at 90°F or hotter
- Precipitation
- About 38.5 in of precipitation a year; about 3.8 in of snowfall
- Electric utility
- City of Seattle serves most local ZIP codes; average residential rate about 12.8 cents per kWh (2023)
- ZIP codes
- 98103, 98105, 98106, 98108, 98112, 98115, 98116, 98117, 98118, 98125, 98126, 98134, 98144, 98199
Plumbing in Seattle: what the local numbers say
Many homes in Seattle, with 53% built before 1980, are now old enough that original water heaters have been replaced more than once while the pipes behind the walls remain from construction. Fixtures, supply stops and tub drains tend to fail first, while hidden supply and drain lines may last longer. Ask a local plumber which parts of your system are original.
Seattle has only about 25 freezing nights a year, so pipe protection is easy to overlook. Plumbing in mild climates is often built with little insulation, and spigots, irrigation backflow assemblies and pipes in attics or garages can be exposed. On the rare hard freeze, these are usually the first parts to fail. A plumber can suggest covers and insulation before a forecast freeze.
About 61% of homes in Seattle heat with electricity, and many of those likely have electric tank water heaters. These have no flue to worry about, but they rely on heating elements and thermostats that wear out, and sediment can make a tank rumble or run out of hot water early. A plumber can drain and flush a tank and check its connections.
With around 38.5 in of precipitation in a typical year, Seattle homes see steady moisture around foundations. Sump pumps, floor drains and downspout connections matter more than in drier regions. Test a sump pump by pouring water into the pit before a heavy storm, and ask a plumber whether your downspouts or footing drains are tied into the sewer, since local rules on that vary.
Seattle has relatively few detached houses, with 37% single-family homes and 44% of households owning their home. Plumbing jobs in multi-unit buildings often involve water heaters in closets, slow shared drain lines, tub and shower leaks that reach the unit below, and shutoff valves that are hard to reach. A plumber will usually want to know whether the problem is inside your unit or in a building line.
Permits, water and local rules in Seattle
- Plumbing permits: Public Health - Seattle and King County, Plumbing and Gas Piping
- Water: Seattle Public Utilities
Plumbing permits come from King County Public Health
In Seattle, plumbing and gas piping permits and inspections are handled by Public Health - Seattle and King County, and the same applies to Clyde Hill and King County areas outside city limits. Applications go through the Public Health Permit Center. The county says homeowners can get a permit to do their own plumbing, which authorizes the homeowner to do that work, and that a hired plumber must be a registered contractor. Properties in other King County cities need permits from that city's building department. Source: King County, Plumbing and gas piping applications and permits.
Water heater installation requirements
King County's water heater guidance says a closed water system needs an expansion tank or other approved thermal expansion device. Seismic bracing must use two 20-gauge sheet metal straps, one on the upper third and one on the lower third of the tank. If the job installs or changes gas piping, a separate gas piping permit is required. Homeowners can verify a plumber's registration with the state before hiring. Source: King County, Installing a new water heater.
Lead in water and household plumbing
Seattle Public Utilities says Seattle's drinking water sources do not contain lead, but lead can leach from plumbing materials such as lead-based solder and brass fixtures. It suggests running the tap for 2 minutes if water has stood in the pipes for over 6 hours, using cold water for drinking and cooking, and choosing low-lead or no-lead fixtures when making plumbing changes. SPU says Seattle has met all Lead and Copper Rule requirements since 2003 and links a map tool to research a service line. Source: Seattle Public Utilities, Lead in Water.
Neighborhoods and districts in Seattle include Ballard, Fremont, Capitol Hill, Queen Anne, Wallingford, Green Lake, Magnolia, University District, Pioneer Square and Belltown.
Common plumbing jobs in Seattle
Before you hire anyone in Seattle, ask whether the job needs a permit, get the scope and price in writing, and verify the plumber's license and insurance with the state or local authority. The Washington plumbing guide explains where to start.
Common questions in Seattle
Could my home in Seattle have polybutylene or other problem pipe?
Homes built from the late 1970s through the mid-1990s sometimes contain polybutylene, a flexible gray or blue plastic supply pipe linked to leaks at its fittings. Copper with lead solder is also possible in homes built before 1986. A local plumber can identify the pipe material at the water heater or main shutoff and explain what to monitor.
Who fixes a leak in my condo or apartment in Seattle?
It usually depends on where the leak starts. Many buildings have shared risers and drain stacks maintained by the owner or association, while fixtures and lines inside your unit may be yours. Check your lease or governing documents and report leaks quickly. Only about 37% of homes in Seattle are detached houses, so shared plumbing is common.
Who issues plumbing permits in Seattle?
Public Health - Seattle and King County issues plumbing and gas piping permits and performs inspections in Seattle, through its online Permit Center. Homeowners can get a permit to do their own plumbing, and a hired plumber must be a registered contractor, according to the county page.
What does a Seattle water heater installation need for earthquake and pressure safety?
King County says a closed water system needs an expansion tank or other approved thermal expansion device. Seismic bracing uses two 20-gauge sheet metal straps, one on the upper third and one on the lower third of the tank. Gas piping changes need a separate gas piping permit.